DMC SD 60 RCS 135 SW & VN - TWO HEAD WIDE BELT SANDER
Grooved rubber coated pressing rollers before and after working unit
2HP variable speed feed motor 3.5-18 m/min (12-60 FPM)
Y-Delta two-stage reduced voltage starter on main motor
Automatic Electronic Table Positioning Device
In-feed / Out-feed extended tables for easier part feeding
Pneumatic On/Off selector of both rollers and pad
Adjustable sanding drum and pad position for micro precision adjustment
Electronic digital thickness readout of work table position
Powered table lifting by means of four heavy duty motor and lifting columns double fastened at both top and bottom of the lifting columns to provide exceptional table stability
Electronic tracking of abrasive belt
Pneumatic belt tensioning with center fulcrum to compensate for tapering of abrasive belt
Front and rear emergency stop button
Amperage meter for main motors allows maximum utilization of available horsepower
Main disconnect switch with the ability to be locked out by padlock
In feed flexible steel hold down, and anti-kickback plate
50 shore, negative profile (waffle style) rubber feed mat
LOGIC 50 K Electronic Programmer for timing/anti-dubbing of the pad
DMC SD 60 RRCS 135 SW & VN - THREE HEAD WIDE BELT SANDER
Grooved rubber coated pressing rollers before and after 2nd and 3rd working unit
Pneumatic floating pressure shoes in first working position
3HP variable speed feed motor 3.5-18 m/min (12-60 FPM)
Y-Delta two-stage reduced voltage starter on main motor
Automatic Electronic Table Positioning Device
In-feed / Out-feed extended tables for easier part feeding
Adjustable sanding drum and pad position for micro precision adjustment and pneumatic On/Off
Electronic digital thickness readout of work table position
Powered table lifting by means of four heavy duty motor and lifting columns double fastened at both top and bottom of the lifting columns to provide exceptional table stability
Electronic tracking of abrasive belt
Pneumatic belt tensioning with center fulcrum to compensate for tapering of abrasive belt
Front and rear emergency stop buttons
Automatic emergency stop of machine for:
sanding belt breaking, tensioning, over tracking
opening of the access door to the operating groups
absence of compressed air
overload on main motors
Amperage meter for main motors allows maximum utilization of available horsepower
Main disconnect switch with the ability to be locked out by padlock
In feed flexible steel hold down, and anti-kickback plate
50 shore, negative profile (waffle style) rubber feed mat
LOGIC SC Electronic Programmer for timing/anti-dubbing of the pad
“Mesar” sectional pad: the best finish with any material. Higher quality results due to the special shape of the sectors that allows the operator to intervene “softly” but also in an “aggressive” way, simply by varying the working pressure. The setting of the pad position and the possibility of using foils of different thickness increases its versality.
“Logic SC” electronic programmer: easily avoid mistakes. Simple and intuitive, allowing the operator to set all processing parameters in sequence and then launch them with the touch of a button. The possibility to store various work programs to retrieve the machine settings most commonly used makes it ideal even for unskilled operators.
Diamond-shaped belt: no slipping of the work pieces. The special geometry of the diamond-shaped profile of the transport belt provides the best traction surface for the work piece and with the increased support area also ensures maximum stability.
Led indicator for panel introduction. Simple and intuitive, communicating to the operator where and when the panel has to be introduced into the machine and optimizing the standard wear of the sanding belt; this ensures a better quality finish and reduced machine costs.
Technical Specifications
Model
SD 60 RCS 135 SW
SD 60 RRCS 135 SW
SD 60 RCS 135 VN
SD 60 RRCS 135 VN
Working Width
1,350 mm (53”)
1,350 mm (53”)
1,350 mm (53”)
1,350 mm (53”)
Number of Heads Available
2
3
2
3
Material Type
Solid Wood
Solid Wood
Veneered / Painted Panels
Veneered / Painted Panels
Feed Motor
2 HP with inverter
3 HP
2 HP with inverter
3 HP
Feed Speed
12 to 60 fpm
12 to 60 fpm
12 to 60 fpm
12 to 60 fpm
Maximum Work piece Thickness
170 mm (6.69”)
170 mm (6.69”)
170 mm (6.69”)
170 mm (6.69”)
Minimum Work piece Length
12.5 inches
12.5 inches
12.5 inches
12.5 inches
Abrasive Belt Size
53” X 85”
53” x 85”
53” x 85”
53” X 85”
Compressed Air Requirements
6 Bar (88 PSI.)
6 Bar (88 PSI.)
6 Bar (88 PSI)
6 Bar (88 PSI.)
Dust Outlets
2 outlets @ 195 mm (7.75”)
3 outlets @ 195mm (7.75”)
2 outlets @ 195 mm (7.75”)
3 outlets @ 195 mm (7.75”)
Exhaust Requirements
3,544 CFM
3,750 CFM
3,544 CFM
3,750 CFM
Power Requirements
150 amps @ 230 Volts/3 phase
96 amps @ 460 Volts/3 phase
130 amps @ 230 Volts/3 phase
60 Volts/3 phase
Technical Specifications
Sander Model
110
135
Working width
mm
1,100
1,350
Min. - max. working thickness
mm
4 - 170
4 - 170
Sanding belts width
mm
1,115
1,370
Sanding belts length
mm
2,150
2,150
Motor power 1st group
kW (Hp)
11 (15)
11 (15)
Motor power 2nd group
kW (Hp)
11 (15)
11 (15)
Feed belt speed
m/min
4.5/9
4.5/9
DMC SD 60 KRCS 110 - 43" WIDE BELT SANDER - PLANER, ONE RUBBER DRUM ROLLER, ONE COMBINATION HEAD
DMC SD 60 RCS 135 - 53" WIDE BELT SANDER - ONE STEEL DRUM ROLLER, ONE COMBINATION HEAD
DMC SD 60 RRCS 135 - 53" WIDE BELT SANDER - ONE STEEL DRUM ROLLER, ONE RUBBER DRUM ROLLER, ONE COMBINATION HEAD
SCM DMC SD 60 | 43" & 53" WIDE BELT SANDER VIDEO
This video is for the Sandya 600 which demonstrates the sanding units featured on the DMC SD 60 sanders.
SCM DMC SD 30, 60, 70, 90 | NEW HMI CONTROLLER VIDEO
