LEADERMAC Model LMC 518S Smartmac
7”(8” optional) 5 Head Moulder
| Specifications |
|
| Thickness Material |
.4”(to 1/4” optional) to 5” |
| Width Material |
.6” to 7” (8” optional) |
| Min length of material |
8” (Butt fed) |
| Axial adjust. side heads |
.8” (20mm) |
| Axial adjust. top/btm heads |
.8” (20mm) |
| Feed Speeds to |
20-85 FPM (6-24 MPM) |
| Net weight approx. |
8,200 lbs. |
DRIVE SYSTEM
- Maintenance free Full Cardan Shaft Drive to feedworks for balanced drive performance, with individual worm reduction gear box to each feed roller station
- Powered rise and fall to extra heavy feed support beam by 1 hp/.75 kw
- Upper support Beam is on large center column for the most rigid upper beam
- All feed rolls and pressures move with top beam rise and fall, including safety switches at extreme
- 6 Top Driven Feed Roll Assemblies (each equipped with Multiple 2” wide rolls that can be quickly spaced/positioned or removed as desired)
- 2 Full Width Driven Bottom Feed Rolls
- Top & Bottom rolls – before first bottom head
- Full Width Bottom Driven Infeed Roll
- Top/Bottom Full Width Powered Outfeed Rolls
- Top Infeed Rolls with pneumatic rise and fall by switch
- Centrally located Pneumatic Pressure Gauges & Controls on Exterior Column
- All Top Rolls are Pneumatically Tensioned. There are 3 different pressurized groups to the Top Rolls. Infeed, Midfeed & Outfeed Top Rolls. Each group has a pressure gauge and regulator for varying pressure setting.
- Top Infeed driven serrated Steel feed rolls up to top head are hardened and satin chromed to resist wear and prevent chips and shavings from sticking to them
- Polyurethane top feed rolls after top head
- Intermediate short stock top driven feed roll station with pneumatic pressure for feeding minimum 8”(200mm) length work pieces. It is easily flipped up for rear side head
- Jog Forward & Jog Reverse to feed with duplicate remote located along the front of the moulder for fast and easy control – Remote includes Beam Up/Down
- Feed roll diameter 5.5” / 140mm
- 5 HP VFD Variable Speed Drive from 20-80 FPM with Digital Speed Readout (can actually run faster if desired)
SPINDLE ASSEMBLIES, CUTTERHEADS & POSITIONING
- All Heads are Standard 6000RPM (7200 rpm optional) and belt driven
- 40mm diameter spindles (1 ½”, 1 13/16” or 50 mm – Optional)
- Spindles are manufactured from SCM-440 tool steel (from Mitsubishi-Japan) with special heat treating to HR 55C Hardness fitted with 2 pairs of Duplex SKF precision high speed Bearings to provide the best cutting stability and accuracy. Spindle Tolerance guaranteed to +/-0.002mm / 0.00007” accuracy. They are permanent grease lubed and are sealed
- Adjustment of all spindles from front – Easy to operate stations
- All spindles have horizontal and vertical adjustment,
- Vertical Spindle – Axial (Vertical) Adjustment – .8”
- Horizontal Spindle – Axial (Horizontal) Adjustment - .8”
- Independent manual vertical adjustment to top head.
- Siko Dual Counters on Near Side Head & Top Head Radial Adjustment for Quick Setup
- All Spindle Axis(Vertical & Horizontal) throughout the Moulder that don’t have Setworks or Dual Siko Counters have Mechanical Position Readouts for Radial & Axial (vertical & horizontal), fast and accurate setting (except 1st Bottom Axial)
- Readouts in Inch
- 1st Bottom Head supplied with Spiral Carbide Cutterhead
- + Set (of 4) Cutterheads Included, serrated back dual angle 12° / 20°
| |
HEAD HP |
CUTTERHEAD SWING |
HOOD SIZE |
| 1) Bottom Head |
7.5 HP |
5” to 6.3”(125 – 160 mm) |
4.9” (125 mm) |
| 2 & 3) Right Side/Left Side Heads |
15 HP |
4” to 7” (100 – 180 mm) |
4.9” (125 mm) |
| 4) Top Head |
15 HP |
4” to 8” (100 – 200 mm) |
4.9” (125 mm) |
| 5) 2nd Bottom Head |
10 HP |
4” to 8” (100 – 200 mm) |
4.9” (125 mm) |
